Cisco Nexus 5600 Series Reference Download Page 94

Page: 94 / 480

Show Commands

show ip pim vrf

MCR-90

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

show ip pim vrf

To display information about IPv4 Protocol Independent Multicast (PIM) by virtual routing and
forwarding (VRF) instance, use the

show ip pim vrf

command.

show ip pim vrf

[

vrf-name

all

default

detail

management

]

Syntax Description

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM by VRF:

switch(config)#

show ip pim vrf

PIM Enabled VRF

VRF Name VRF Table Interface BFD

ID ID Count Enabled

default 1 0x00000001 1 no

switch(config)#

This example shows how to display the detailed information about IPv4 PIM by VRF:

switch#

show ip pim vrf detail

PIM Enabled VRF

VRF Name VRF Table Interface BFD

vrf-name

(Optional) VRF name. The name can be a maximum of 32 alphanumeric characters
and is case sensitive.

all

(Optional) Specifies all VRFs.

default

(Optional) Specifies the default VRF.

detail

(Optional) Displays detailed PIM VRF information.

management

(Optional) Specifies the management VRF.

Release

Modification

5.0(3)N1(1)

This command was introduced.

5.0(2)

Information on Bidirectional Forwarding Detection (BFD) was added.

Summary of Contents for Nexus 5600 Series

































































































































































































































































































































































































































































































Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands

Cisco Nexus 5600 Series, Reference

Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands