Cisco Nexus 5600 Series Reference Download Page 28

Page: 28 / 480

Show Commands

show forwarding distribution multicast route

MCR-24

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

show forwarding distribution multicast route

To display information about the multicast Forwarding Information Base (FIB) distribution routes, use
the

show forwarding distribution multicast route

command.

show forwarding distribution

[

ipv4

]

multicast route

[

table

vrf

vrf_name

] [[

group

{

group-addr

[

mask

] |

group-prefix

}] [

source

{

source-addr

[

source-mask

] |

source-prefix

}] |

summary

]

Syntax Description

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Usage Guidelines

This command does not require a license.

(Optional) Specifies IPV4 information.

ipv4

(Optional) Specifies IPV4 information.

table

(Optional) Specifies the multicast routing table ID. The range is from 0 to
2147483647.

vrf

vrf_name

(Optional) Specifies a virtual routing and forwarding (VRF) name. The name can be
a maximum of 32 alphanumeric characters.

group

(Optional) Specifies an IPv4 multicast group.

group-addr

IPv4 multicast group address.

mask

(Optional) Mask for the group address.

group-prefix

(Optional) IPv4 multicast group prefix.

source

(Optional) Specifies an IPv4 multicast source.

source-addr

IPv4 source address.

source-mask

(Optional) Mask for the group address.

source-prefix

(Optional) IPv4 multicast source prefix.

summary

(Optional) Displays the route counts.

Release

Modification

5.0(3)N1(1)

This command was introduced.

Summary of Contents for Nexus 5600 Series

































































































































































































































































































































































































































































































Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands

Cisco Nexus 5600 Series, Reference

Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands