Cisco Nexus 5600 Series Reference Download Page 316

Page: 316 / 480

312

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

Chapter I Commands

ip pim anycast-rp

To configure an IPv4 Protocol Independent Multicast (PIM) Anycast-RP peer for the specified
Anycast-RP address, use the

ip pim anycast-rp

command. To remove the peer, use the

form of this

command.

ip pim anycast-rp

anycast-rp rp-addr

no ip pim anycast-rp

anycast-rp rp-addr

Syntax Description

Command Default

None

Command Modes

Global configuration mode
VRF configuration mode

Supported User Roles

network-admin
vdc-admin

Command History

Usage Guidelines

Each command with the same Anycast-RP address forms an Anycast-RP set. The IP addresses of RPs
are used for communication with RPs in the set.

This command requires the LAN Base Services license.

Examples

This example shows how to configure a PIM Anycast-RP peer:

switch#

configure terminal

switch(config)#

ip pim anycast-rp 192.0.2.3 192.0.2.31

This example shows how to remove a peer:

switch#

configure terminal

switch(config)#

no ip pim anycast-rp 192.0.2.3 192.0.2.31

Related Commands

anycast-rp

Anycast-RP address of the peer.

rp-addr

Address of RP in the Anycast-RP set.

Release

Modification

6.0(2)N1(1)

This command was introduced.

Command

Description

show ip pim rp

Displays information about PIM RPs.

Summary of Contents for Nexus 5600 Series

































































































































































































































































































































































































































































































Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands

Cisco Nexus 5600 Series, Reference

Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands