Cisco Nexus 5600 Series Reference Download Page 397

Page: 397 / 480

393

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

Chapter I Commands

ipv6 pim register-rate-limit

To configure a rate limit for IPv6 Protocol Independent Multicast (PIM6) data registers, use the

ipv6

pim register-rate-limit

command. To remove a rate limit, use the

form of this command.

ipv6 pim register-rate-limit

rate

no ipv6 pim register-rate-limit

[

rate

]

Syntax Description

Defaults

None

Command Modes

Global configuration mode

Supported User Roles

network-admin
vdc-admin

Command History

Usage Guidelines

This command does not require a license.

Examples

This example shows how to configure a rate limit for PIM6 data registers:

switch(config)#

ipv6 pim register-rate-limit 1000

This example shows how to remove a rate limit:

switch(config)#

no ipv6 pim register-rate-limit

Related Commands

rate

Rate in packets per second. The range is from 1 to 65,535.

Release

Modification

5.0(3)N1(1)

This command was introduced.

Command

Description

show ipv6 pim
interface

Displays information about PIM6 interfaces.

Summary of Contents for Nexus 5600 Series

































































































































































































































































































































































































































































































Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands

Cisco Nexus 5600 Series, Reference

Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands