Cisco Nexus 5600 Series Reference Download Page 423

Page: 423 / 480

419

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

Chapter Show Commands

show ip pim group-range

To display information about the group ranges for IPv4 Protocol Independent Multicast (PIM), use the

show ip pim group-range

command.

show ip pim group-range

[

group

] [

vrf

{

vrf-name

all

default

management

}]

Syntax Description

Command Default

None

Command Modes

Any command mode

Supported User Roles

network-admin
network-operator
vdc-admin
vdc-operator

Command History

Usage Guidelines

This command requires the LAN Base Services license.

Examples

This example shows how to display information about IPv4 PIM group ranges:

switch(config)#

show ip pim group-range

PIM Group-Range Configuration for VRF "default"

Group-range Mode RP-address Shared-tree-only range

232.0.0.0/8 SSM - -

switch(config)#

group

(Optional) Group address.

vrf

(Optional) Applies to a virtual routing and forwarding (VRF) instance.

vrf-name

VRF name. The name can be a maximum of 32 alphanumeric characters and is case
sensitive.

all

Specifies that all VRF entries be cleared from the IPv4 multicast routing table.

default

Specifies that the default VRF entry be cleared from the IPv4 multicast routing table.

management

Specifies that the management VRF entry be cleared from the IPv4 multicast routing
table.

Release

Modification

6.0(2)N1(1)

This command was introduced.

Summary of Contents for Nexus 5600 Series

































































































































































































































































































































































































































































































Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands

Cisco Nexus 5600 Series, Reference

Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands