Cisco Nexus 5600 Series Reference Download Page 362

Page: 362 / 480

358

Cisco Nexus 5600 Series NX-OS Multicast Routing Command Reference

OL-31626-01

Chapter I Commands

ip pim spt-threshold infinity

To create the IPv4 Protocol Independent Multicast (PIM) (*, G) state only (where no source state is
created), use the

ip pim spt-threshold infinity

command. To remove the creation of the shared tree state

only, use the

form of this command.

ip pim spt-threshold infinity group-list

route-map-name

no ip pim spt-threshold infinity

[

group-list

route-map-name

]

Syntax Description

Command Default

None

Command Modes

Global configuration mode
VRF configuration mode

Supported User Roles

network-admin
vdc-admin

Command History

Usage Guidelines

You can specify up to 500 sequence lines in a route map.

The

match ip multicast

command is the only match command that is evaluated in the route map. You

can specify the group prefix to filter messages with the

match ip multicast

command.

You must have enabled PIM before you can use the

ip pim spt-threshold infinity

command.

Note

This command is not supported for virtual port channels (vPC/vPC+).

This command requires the Enterprise Services license.

Note

The

ip pim use-shared-tree-only group-list

command performs the same function as the

ip pim

spt-threshold infinity group-list

command. You can choose to use either command to implement this

task.

route-map-name Route-map policy name that defines the group prefixes where this feature is applied.

A route-map policy name can be a maximum of 100 alphanumeric characters.

Release

Modification

7.0(0)N1(1)

This command was introduced.

Summary of Contents for Nexus 5600 Series

































































































































































































































































































































































































































































































Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands

Cisco Nexus 5600 Series, Reference

Search results

Summary of Contents for Nexus 5600 Series

Reviews:

Related manuals for Nexus 5600 Series

Brands by name

Popular brands