manualshive.com logo in svg

Cisco IE 3000, Software Configuration Manual

Download the free Software Configuration Manual for Cisco IE 3000, a cutting-edge product providing seamless connectivity and industrial Ethernet communications. Enhance your understanding of its features and functionalities, optimizing your network infrastructure. Visit manualshive.com to access the comprehensive manual and elevate your Cisco IE 3000 experience.

Share
Download
background image

 

16-2

Cisco IE 3000 Switch Software Configuration Guide

OL-13018-03

Chapter 16      Configuring VTP

Understanding VTP

These sections contain this conceptual information:

  •

The VTP Domain, page 16-2

  •

VTP Modes, page 16-3

  •

VTP Advertisements, page 16-3

  •

VTP Version 2, page 16-4

  •

VTP Pruning, page 16-4

The VTP Domain 

A VTP domain (also called a VLAN management domain) consists of one switch or several 
interconnected switches under the same administrative responsibility sharing the same VTP domain 
name. A switch can be in only one VTP domain. You make global VLAN configuration changes for the 
domain.

By default, the switch is in the VTP no-management-domain state until it receives an advertisement for 
a domain over a trunk link (a link that carries the traffic of multiple VLANs) or until you configure a 
domain name. Until the management domain name is specified or learned, you cannot create or modify 
VLANs on a VTP server, and VLAN information is not propagated over the network.

If the switch receives a VTP advertisement over a trunk link, it inherits the management domain name 
and the VTP configuration revision number. The switch then ignores advertisements with a different 
domain name or an earlier configuration revision number.

Caution

Before adding a VTP client switch to a VTP domain, always verify that its VTP configuration revision 
number is 

lower

 than the configuration revision number of the other switches in the VTP domain. 

Switches in a VTP domain always use the VLAN configuration of the switch with the highest VTP 
configuration revision number. If you add a switch that has a revision number higher than the revision 
number in the VTP domain, it can erase all VLAN information from the VTP server and VTP domain. 
See the 

“Adding a VTP Client Switch to a VTP Domain” section on page 16-14

 for the procedure for 

verifying and resetting the VTP configuration revision number.

When you make a change to the VLAN configuration on a VTP server, the change is propagated to all 
switches in the VTP domain. VTP advertisements are sent over all IEEE trunk connections, including 
IEEE 802.1Q. VTP dynamically maps VLANs with unique names and internal index associates across 
multiple LAN types. Mapping eliminates excessive device administration required from network 
administrators.

If you configure a switch for VTP transparent mode, you can create and modify VLANs, but the changes 
are not sent to other switches in the domain, and they affect only the individual switch. However, 
configuration changes made when the switch is in this mode are saved in the switch running 
configuration and can be saved to the switch startup configuration file.

For domain name and password configuration guidelines, see the 

“VTP Configuration Guidelines” 

section on page 16-7

.

Summary of Contents for IE 3000











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 3000

Patton electronics 2888 Quick Start Manual preview
2888
Brand: Patton electronics Pages: 8
Vanguard 342 Quick Reference Manual preview
342
Brand: Vanguard Pages: 4
MiLAN E-MCC-1600 Install Manual preview
E-MCC-1600
Brand: MiLAN Pages: 1
Symantec PacketShaper PS-S200 Quick Start Manual preview
PacketShaper PS-S200
Brand: Symantec Pages: 2
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
VCS VIP 1000 User Manual preview
VIP 1000
Brand: VCS Pages: 118
Observint NVR16 Firmware User Manual preview
NVR16
Brand: Observint Pages: 117
TP-Link TL-SL2226P+ User Manual preview
TL-SL2226P+
Brand: TP-Link Pages: 37
Digisol DG-BG100 User Manual preview
DG-BG100
Brand: Digisol Pages: 81
Behringer B-Control Fader BCF2000 Quick Start Manual preview
B-Control Fader BCF2000
Brand: Behringer Pages: 13
Wave wifi MBR Series Quick Start Manual preview
MBR Series
Brand: Wave wifi Pages: 3
DHD Power Cruiser 52/XR Manual preview
52/XR
Brand: DHD Power Cruiser Pages: 60
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
R.V.R. Elettronica PTX30-UHT Installation, Technical And Maintenance Manual preview
PTX30-UHT
Brand: R.V.R. Elettronica Pages: 171
Axtrinet APG200 User Manual preview
APG200
Brand: Axtrinet Pages: 49
Digi Transport WR41-C Installation Manual preview
Transport WR41-C
Brand: Digi Pages: 7
Asus WL-167g deluxe User Manual preview
WL-167g deluxe
Brand: Asus Pages: 44

Brands by name

Popular brands

Load more brands