manualshive.com logo in svg

Cisco IE 3000, Software Configuration Manual

Download the free Software Configuration Manual for Cisco IE 3000, a cutting-edge product providing seamless connectivity and industrial Ethernet communications. Enhance your understanding of its features and functionalities, optimizing your network infrastructure. Visit manualshive.com to access the comprehensive manual and elevate your Cisco IE 3000 experience.

Share
Download
background image

C H A P T E R

 

26-1

Cisco IE 3000 Switch Software Configuration Guide

OL-13018-03

26

Configuring Port-Based Traffic Control

This chapter describes how to configure the port-based traffic control features on the IE 3000 switch. 

Note

For complete syntax and usage information for the commands used in this chapter, see the command 
reference

 

for this release.

This chapter consists of these sections:

  •

Configuring Storm Control, page 26-1

  •

Configuring Protected Ports, page 26-6

  •

Configuring Port Blocking, page 26-7

  •

Configuring Port Security, page 26-8

  •

Displaying Port-Based Traffic Control Settings, page 26-19

Configuring Storm Control

These sections contain this conceptual and configuration information:

  •

Understanding Storm Control, page 26-1

  •

Default Storm Control Configuration, page 26-3

  •

Configuring Storm Control and Threshold Levels, page 26-3

  •

Configuring Small-Frame Arrival Rate, page 26-5

Understanding Storm Control

Storm control prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm 
on one of the physical interfaces. A LAN storm occurs when packets flood the LAN, creating excessive 
traffic and degrading network performance. Errors in the protocol-stack implementation, mistakes in 
network configurations, or users issuing a denial-of-service attack can cause a storm. 

Storm control (or traffic suppression) monitors packets passing from an interface to the switching bus 
and determines if the packet is unicast, multicast, or broadcast. The switch counts the number of packets 
of a specified type received within the 1-second time interval and compares the measurement with a 
predefined suppression-level threshold. 

Summary of Contents for IE 3000











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 3000

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
Rain Bird E-3 Installation, Programming & Operation Manual preview
E-3
Brand: Rain Bird Pages: 17
YASKAWA SI-EP3/V Installation Manual preview
SI-EP3/V
Brand: YASKAWA Pages: 68
Lancom 7100 VPN Manual preview
7100 VPN
Brand: Lancom Pages: 70
Patton electronics SMARTNODE 4950 Quick Start Manual preview
SMARTNODE 4950
Brand: Patton electronics Pages: 12
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
WABCO CAN Router Manual preview
CAN Router
Brand: WABCO Pages: 29
ACTi GNR-310 Quick Installation Manual preview
GNR-310
Brand: ACTi Pages: 12
Maipu SM3100-28TC-AC Install Manual preview
SM3100-28TC-AC
Brand: Maipu Pages: 19
AIC SB401-MN User Manual preview
SB401-MN
Brand: AIC Pages: 88
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
l-com HA72170-NF Installation Manual preview
HA72170-NF
Brand: l-com Pages: 2
Comelit IPNVR016A User Manual preview
IPNVR016A
Brand: Comelit Pages: 140
SMC Networks TigerSwitch 100 SMC6924VF Management Manual preview
TigerSwitch 100 SMC6924VF
Brand: SMC Networks Pages: 174
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168

Brands by name

Popular brands

Load more brands