Cisco IE 3000 Software Configuration Manual Download Page 497 | Manualshive

Page: 497 / 874

background image

C H A P T E R

25-1

Cisco IE 3000 Switch Software Configuration Guide

OL-13018-03

25

Configuring IGMP Snooping and MVR

This chapter describes how to configure Internet Group Management Protocol (IGMP) snooping on the
IE 3000 switch, including an application of local IGMP snooping, Multicast VLAN Registration (MVR).
It also includes procedures for controlling multicast group membership by using IGMP filtering and
procedures for configuring the IGMP throttling action.

Note

For complete syntax and usage information for the commands used in this chapter, see the switch

command reference for this release and the “IP Multicast Routing Commands” section in the

Cisco IOS

IP Command Reference, Volume 3 of 3:Multicast, Release 12.2

from the Cisco.com page under

Documentation

>

Cisco IOS Software

>

12.2 Mainline

>

Command References

.

This chapter consists of these sections:

•

Understanding IGMP Snooping, page 25-1

•

Configuring IGMP Snooping, page 25-6

•

Displaying IGMP Snooping Information, page 25-15

•

Understanding Multicast VLAN Registration, page 25-16

•

Configuring MVR, page 25-19

•

Displaying MVR Information, page 25-23

•

Configuring IGMP Filtering and Throttling, page 25-23

•

Displaying IGMP Filtering and Throttling Configuration, page 25-28

Note

You can either manage IP multicast group addresses through features such as IGMP snooping and MVR,
or you can use static IP addresses.

Understanding IGMP Snooping

Layer 2 switches can use IGMP snooping to constrain the flooding of multicast traffic by dynamically
configuring Layer 2 interfaces so that multicast traffic is forwarded to only those interfaces associated
with IP multicast devices. As the name implies, IGMP snooping requires the LAN switch to snoop on
the IGMP transmissions between the host and the router and to keep track of multicast groups and
member ports. When the switch receives an IGMP report from a host for a particular multicast group,

«
...
495
496
497
498
499
...
»

Summary of Contents for IE 3000











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for IE 3000

OfficeConnect 1600

Brand: 3Com Pages: 8

Brand: 3Com Pages: 8

Brand: Magnadyne Pages: 13

Brand: Vanguard Pages: 4

Brand: ZyXEL Communications Pages: 485

Brand: ZyXEL Communications Pages: 299

JetNet 3508-LVDC

Brand: Korenix Pages: 16

Brand: QUNDIS Pages: 42

Brand: Network Critical Pages: 200

Brand: INNOSILICON Pages: 11

Brand: ZyXEL Communications Pages: 66

Brand: CopperOptics Pages: 12

Brand: Neousys Technology Pages: 39

Brand: B&B Electronics Pages: 2

Brand: Supero Pages: 54

Passport 8608GTE

Brand: Nortel Pages: 10

Brand: Datavideo Pages: 71

CANopen Communication Module DVPCP02-H2

Brand: Delta Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands