manualshive.com logo in svg

Cisco Catalyst 3550, Software Configuration Manual

The Cisco Catalyst 3550 is a powerful network switch that provides high-performance networking capabilities. Ensure a smooth installation with the comprehensive Installation Manual, available for free download from manualshive.com. This manual offers step-by-step instructions and valuable insights to maximize the potential of your Catalyst 3550, delivering exceptional networking performance.

Share
Download
background image

 

9-7

Catalyst 3550 Multilayer Switch Software Configuration Guide

78-11194-03

Chapter 9      Creating and Maintaining VLANs

Using the VLAN Trunking Protocol

Figure 9-2

Flooding Traffic without VTP Pruning

Figure 9-3

 shows a switched network with VTP pruning enabled. The broadcast traffic from Switch 1 is 

not forwarded to Switches 3, 5, and 6 because traffic for the Red VLAN has been pruned on the links 
shown (Port 5 on Switch 2 and Port 4 on Switch 4). 

Figure 9-3

Optimized Flooded Traffic with VTP Pruning

Enabling VTP pruning on a VTP server enables pruning for the entire management domain. See the 

“Enabling VTP Pruning” section on page 9-13

. VTP pruning takes effect several seconds after you 

enable it. VTP pruning does not prune traffic from VLANs that are pruning-ineligible. VLAN 1 is always 
pruning-ineligible; traffic from VLAN 1 cannot be pruned.

VTP pruning is not designed to function in VTP transparent mode. If one or more switches in the 
network are in VTP transparent mode, you should do one of these:

•

Turn off VTP pruning in the entire network.

•

Turn off VTP pruning by making all VLANs on the trunk of the switch upstream to the VTP 
transparent switch pruning ineligible.

Switch 4

Switch 5

Switch 3

Switch 6

Switch 1

Switch 2

Port 1

Port 2

Red 

VLAN

45826

Switch 4

Switch 5

Switch 3

Switch 6

Switch 1

Switch 2

Port 1

Port 2

Red 

VLAN

45827

Port
4

Port
5

Flooded traffic
is pruned.

Flooded traffic
is pruned.

Summary of Contents for Catalyst 3550































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3550

AMX Modero ViewPoint MVP-5100 Operation/Reference Manual preview
Modero ViewPoint MVP-5100
Brand: AMX Pages: 190
RTS RTS ISDN 2002 Operator'S Manual preview
RTS ISDN 2002
Brand: RTS Pages: 51
Red Hat CERTIFICATE SYSTEM 8.0 - ADMINISTRATION Admin Manual preview
CERTIFICATE SYSTEM 8.0 - ADMINISTRATION
Brand: Red Hat Pages: 564
2Wire Wireless PCI Adapter Driver Installation Instructions preview
Wireless PCI Adapter Driver
Brand: 2Wire Pages: 4
APPLIED ACOUSTICS SYSTEMS ULTRA ANALOG User Manual preview
ULTRA ANALOG
Brand: APPLIED ACOUSTICS SYSTEMS Pages: 60
DivX 10 User Manual preview
10
Brand: DivX Pages: 59
Intel Active Management Technology v5.0 Administrator'S Manual preview
Active Management Technology v5.0
Brand: Intel Pages: 143
UNIBLUE RegistryBooster 2010 Product Manual preview
RegistryBooster 2010
Brand: UNIBLUE Pages: 11
Autodesk 507B1-90A211-1301 - NavisWorks Manage 2010 User Manual preview
507B1-90A211-1301 - NavisWorks Manage 2010
Brand: Autodesk Pages: 472
IBM Hub/Switch Installation Manual preview
Hub/Switch
Brand: IBM Pages: 590
IBM RELEASE 7.3 Management Manual preview
RELEASE 7.3
Brand: IBM Pages: 388
National Instruments NI-VXI User Manual preview
NI-VXI
Brand: National Instruments Pages: 149
TANDBERG MOVI D14409.01 User Manual preview
MOVI D14409.01
Brand: TANDBERG Pages: 17
Xerox DocuColor 242 User Manual preview
DocuColor 242
Brand: Xerox Pages: 32
Xerox DocuShare 6.0 User Manual preview
DocuShare 6.0
Brand: Xerox Pages: 20
TC Electronic Intelligent Vocal Harmony Harmony4 Manual preview
Intelligent Vocal Harmony Harmony4
Brand: TC Electronic Pages: 21
Brocade Communications Systems Brocade 8/12c Command Reference Manual preview
Brocade 8/12c
Brand: Brocade Communications Systems Pages: 1132
Tadiran Telecom Coral SeaBeam Installation And Configuration Reference Manual preview
Coral SeaBeam
Brand: Tadiran Telecom Pages: 68

Brands by name

Popular brands

Load more brands