manualshive.com logo in svg

Cisco Catalyst 3550, Software Configuration Manual

The Cisco Catalyst 3550 is a powerful network switch that provides high-performance networking capabilities. Ensure a smooth installation with the comprehensive Installation Manual, available for free download from manualshive.com. This manual offers step-by-step instructions and valuable insights to maximize the potential of your Catalyst 3550, delivering exceptional networking performance.

Share
Download
background image

C H A P T E R

 

23-1

Catalyst 3550 Multilayer Switch Software Configuration Guide

78-11194-03

23

Configuring HSRP

This chapter describes how to use Hot Standby Router Protocol (HSRP) to provide routing redundancy 
for routing IP traffic without being dependent on the availability of any single router. To use this feature, 
you must have the enhanced multilayer software image installed on your switch. All Catalyst 3550 
Gigabit Ethernet switches ship with the enhanced multilayer software image (EMI) installed. Catalyst 3550 
Fast Ethernet switches can be shipped with either the standard multilayer software image (SMI) or EMI 
pre-installed. You can order the Enhanced Multilayer Software Image Upgrade kit to upgrade Catalyst 3550 
Fast Ethernet switches from the SMI to the EMI.

Note

You can also use a version of HSRP in Layer 2 mode to configure a redundant command switch to 
take over cluster management if the cluster command switch fails. For more information about 
clustering, see 

Chapter 5, “Clustering Switches.”

Note

For complete syntax and usage information for the commands used in this chapter, refer to the 
Catalyst 3550 Multilayer Switch Command Reference and the Cisco IOS IP and IP Routing 
Command Reference for Release 12.1.

This chapter consists of these sections:

•

Understanding HSRP, page 23-1

•

Configuring HSRP, page 23-3

•

Displaying HSRP Configurations, page 23-10

Understanding HSRP

HSRP is Cisco’s standard method of providing high network availability by providing first-hop 
redundancy for IP hosts on an IEEE 802 LAN configured with a default gateway IP address. HSRP 
routes IP traffic without relying on the availability of any single router. It enables a set of router 
interfaces to work together to present the appearance of a single virtual router or default gateway to the 
hosts on a LAN. When HSRP is configured on a network or segment, it provides a virtual Media Access 
Control (MAC) address and an IP address that is shared among a group of configured routers. HSRP 
allows two or more HSRP-configured routers to use the MAC address and IP network address of a virtual 
router. The virtual router does not exist; it represents the common target for routers that are configured 
to provide backup to each other. One of the routers is selected to be the active router and another to be 
the standby router, which assumes control of the group MAC address and IP address should the 
designated active router fail.

Summary of Contents for Catalyst 3550































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3550

AMX I!-TIMEMANAGER Instruction Manual preview
I!-TIMEMANAGER
Brand: AMX Pages: 16
Sony D-NE329SP - Atrac Cd Walkman Portable Player Specifications preview
D-NE329SP - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 2
Sony D-NE20 - Atrac Cd Walkman Specifications preview
D-NE20 - Atrac Cd Walkman
Brand: Sony Pages: 2
Sony D-NE326CK - Atrac Cd Walkman Portable Player Specifications preview
D-NE326CK - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 2
Sony D-NE329SP - Atrac Cd Walkman Portable Player Service Manual preview
D-NE329SP - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 32
Sony D-NE1 - Portable Cd Player Service Manual preview
D-NE1 - Portable Cd Player
Brand: Sony Pages: 34
Sony D-NE326CK - Atrac Cd Walkman Portable Player Operating Instructions Manual preview
D-NE326CK - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 35
Sony D-NE1 - Portable Cd Player Operating Instructions Manual preview
D-NE1 - Portable Cd Player
Brand: Sony Pages: 116
GRASS VALLEY Concerto Instruction Manual preview
Concerto
Brand: GRASS VALLEY Pages: 174
IBM High Performance Storage System HPSS Installation Manual preview
High Performance Storage System HPSS
Brand: IBM Pages: 311
KAPERSKY ANTI-VIRUS - FOR SUN SOLARIS MAIL SERVER User Manual preview
ANTI-VIRUS - FOR SUN SOLARIS MAIL SERVER
Brand: KAPERSKY Pages: 254
Bai cells EG7035 User Manual preview
EG7035
Brand: Bai cells Pages: 24
Ableton Live Reference Manual preview
Live
Brand: Ableton Pages: 535
Waves The King's User Manual preview
The King's
Brand: Waves Pages: 16
Omron CX-POSITIO Specifications preview
CX-POSITIO
Brand: Omron Pages: 2
Omron CX-PROCESS Brochure preview
CX-PROCESS
Brand: Omron Pages: 7
Omron CX-MOTION Specifications preview
CX-MOTION
Brand: Omron Pages: 2
Omron CX-ONE - BROCHURE 1 Brochure preview
CX-ONE - BROCHURE 1
Brand: Omron Pages: 6

Brands by name

Popular brands

Load more brands