manualshive.com logo in svg

Cisco Catalyst 3550, Software Configuration Manual

The Cisco Catalyst 3550 is a powerful network switch that provides high-performance networking capabilities. Ensure a smooth installation with the comprehensive Installation Manual, available for free download from manualshive.com. This manual offers step-by-step instructions and valuable insights to maximize the potential of your Catalyst 3550, delivering exceptional networking performance.

Share
Download
background image

C H A P T E R

 

17-1

Catalyst 3550 Multilayer Switch Software Configuration Guide

78-11194-03

17

Configuring System Message Logging

This chapter describes how to configure system message logging on your switch.

Note

For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 
IOS Configuration Fundamentals Command Reference for Release 12.1.

This chapter consists of these sections:

•

Understanding System Message Logging, page 17-1

•

Configuring System Message Logging, page 17-2

•

Displaying the Logging Configuration, page 17-12

Understanding System Message Logging

By default, switches send the output from system messages and debug privileged EXEC commands to 
a logging process. The logging process controls the distribution of logging messages to various 
destinations, such as the logging buffer, terminal lines, or a UNIX syslog server, depending on your 
configuration. The process also sends messages to the console. 

Note

The syslog format is compatible with 4.3 BSD UNIX.

When the logging process is disabled, messages are sent only to the console. The messages are sent as 
they are generated, so message and debug output are interspersed with prompts or output from other 
commands. Messages are displayed on the console after the process that generated them has finished.

You can set the severity level of the messages to control the type of messages displayed on the console 
and each of the destinations. You can timestamp log messages or set the syslog source address to enhance 
real-time debugging and management. For information on possible messages, refer to the Catalyst 3550 
Multilayer Switch System Message Guide for this release.

You can access logged system messages by using the switch command-line interface (CLI) or by saving 
them to a properly configured syslog server. The switch software saves syslog messages in an internal 
buffer. You can remotely monitor system messages by accessing the switch through Telnet, through the 
console port, or by viewing the logs on a syslog server.

Summary of Contents for Catalyst 3550































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Catalyst 3550

Garmin 010-10307-00 - MapSource Fishing Hot Spots Manual Do Usuário preview
010-10307-00 - MapSource Fishing Hot Spots
Brand: Garmin Pages: 30
NETGEAR GS700AT Series Installation Manual preview
GS700AT Series
Brand: NETGEAR Pages: 2
ICP ICPCON User Manual preview
ICPCON
Brand: ICP Pages: 77
MACROMEDIA COLDFUSION MX 61-GETTING STARTED BUILDING COLDFUSION... Getting Started preview
COLDFUSION MX 61-GETTING STARTED BUILDING COLDFUSION...
Brand: MACROMEDIA Pages: 134
Red Hat JBoss Developer Studio 3.0 User Reference Manual preview
JBoss Developer Studio 3.0
Brand: Red Hat Pages: 78
Panasonic PTF100NTU - LCD PROJECTOR Specifications preview
PTF100NTU - LCD PROJECTOR
Brand: Panasonic Pages: 2
Panasonic SZ-CB8P Operating Instructions preview
SZ-CB8P
Brand: Panasonic Pages: 4
Panasonic PT-LW80NT Spec File preview
PT-LW80NT
Brand: Panasonic Pages: 10
Panasonic Media Manager V2.1 Basic Operating Instructions Manual preview
Media Manager V2.1
Brand: Panasonic Pages: 28
Panasonic Lumix VQT0U14 ( ) Operating Instructions Manual preview
Lumix VQT0U14 ( )
Brand: Panasonic Pages: 36
Panasonic WJ-ASC960 Operating Instructions Manual preview
WJ-ASC960
Brand: Panasonic Pages: 70
Panasonic PANATERM Ver. 3.7 Instruction Manual preview
PANATERM Ver. 3.7
Brand: Panasonic Pages: 78
Panasonic Voice Editing Ver.2.0 Operating Instructions Manual preview
Voice Editing Ver.2.0
Brand: Panasonic Pages: 132
Panasonic WV-AS65 Operating Instructions Manual preview
WV-AS65
Brand: Panasonic Pages: 156
Sharp PixLab Online Manual preview
PixLab
Brand: Sharp Pages: 12
British Telecom Tyne Operating Instructions & User Manual preview
Tyne
Brand: British Telecom Pages: 4
2Wire Wireless PCI Adapter Driver Installation Instructions preview
Wireless PCI Adapter Driver
Brand: 2Wire Pages: 4
GRASS VALLEY Concerto Instruction Manual preview
Concerto
Brand: GRASS VALLEY Pages: 174

Brands by name

Popular brands

Load more brands