manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

Description

Field

Frequency of the wavelength in terahertz.

frequency (THz)

Wavelength in nanometers.

wavelength (nm)

Related Commands

Description

Command

Configures the transport administration state on a DWDM port.

admin-state, on page 3

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

62

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

show controller dwdm

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

OlenCom MG-iP Series Reference Manual preview
MG-iP Series
Brand: OlenCom Pages: 299
Amit IOG761 User Manual preview
IOG761
Brand: Amit Pages: 395
Innovaphone IP 400 Administrator'S Manual preview
IP 400
Brand: Innovaphone Pages: 164
Siemens SMG 71 Installation Instructions preview
SMG 71
Brand: Siemens Pages: 2
Siemens VNT Installation Instructions Manual preview
VNT
Brand: Siemens Pages: 8
Siemens VersiComm VC1COMMA Installation And Operation Manual preview
VersiComm VC1COMMA
Brand: Siemens Pages: 22
Siemens SIRIUS 3RK3141 Series Original Operating Instructions preview
SIRIUS 3RK3141 Series
Brand: Siemens Pages: 19
Siemens SIMATIC RTLS4330G Operating Instructions Manual preview
SIMATIC RTLS4330G
Brand: Siemens Pages: 28
Siemens Tiastar LV MCC Instruction Manual preview
Tiastar LV MCC
Brand: Siemens Pages: 48
Siemens Sinamics Connect Series Operating Instructions Manual preview
Sinamics Connect Series
Brand: Siemens Pages: 101
Siemens WTT563 Series Operating And Installation Instructions preview
WTT563 Series
Brand: Siemens Pages: 124
Siemens SIMATIC S7-200 System Manual preview
SIMATIC S7-200
Brand: Siemens Pages: 866
Solidtronic RT-RoIP2-Azetti User Manual preview
RT-RoIP2-Azetti
Brand: Solidtronic Pages: 8
Solidtronic RT-RoIP2-Zello User Manual preview
RT-RoIP2-Zello
Brand: Solidtronic Pages: 8
Check Point QUANTUM SPARK 1600 Administration Manual preview
QUANTUM SPARK 1600
Brand: Check Point Pages: 285
Endress+Hauser Fieldgate FXA520 Operating Instructions Manual preview
Fieldgate FXA520
Brand: Endress+Hauser Pages: 108
Watchguard Firebox X Series Quick Start Manual preview
Firebox X Series
Brand: Watchguard Pages: 37
RTA 460BM Product User Manual preview
460BM
Brand: RTA Pages: 58

Brands by name

Popular brands

Load more brands