Cisco ASR 9000 Series Page 380 Command Reference Manual Download

Page: 380 / 1138

Table 20: show ethernet lmi interfaces detail Field Descriptions

Description

Field

Name of the interface running the E-LMI protocol.

Interface:

Status of the E-LMI protocol on the interface. Possible
values are Up, Down, or Unknown (PVT disabled).

Ether LMI Link Status:

Name of the UNI as configured by the

ethernet uni

command. This output field does not appear if the

UNI ID is not configured.

UNI Id:

Status of the interface line protocol. Possible values
are Up, Down, or Admin-Down.

Line Protocol State:

Maximum Transmission Unit of the interface and the
number (

) of E-LMI PDUs of that size required to

send one full status report.

MTU (

PDUs reqd for full report)

Map type, which describes how CE VLAN IDs are
mapped to specific EVCs. Possible valued for

type

are Bundling, All to One Bundling, or Service
Multiplexing with no bundling. The number

EVCs in the map are displayed in parentheses.

CE-VLAN/EVC Map Type:

type

(

EVCs)

Value of the MEF N393 Status Counter as configured
by the

status-counter

command.

Configuration: Status counter

Value of the MEF T392 Polling Verification Timer
(in seconds) as configured by the

polling-verification-timer

command. Displays

"disabled" if the PVT is turned off.

Polling Verification Timer

Current value of the Data Instance.

Last Data Instance Sent:

Values of the last sent (

) and received (

) sequence

numbers as reported in sent PDUs.

Last Sequence Numbers: Sent

, Received

Number of times the specified types of reliability
errors have occurred since the protocol was enabled
on the interface or counters were cleared.

Reliability Errors:

(Status Enq Timeouts, Invalid Report Type, and
Invalid Sequence Number)

Number of times the specified types of protocol errors
have occurred since the protocol was enabled on the
interface or counters were cleared.

Protocol Errors:

(Malformed PDUs, Invalid Message Type, Duplicated
IE, and others)

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

360

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet lmi interfaces

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands