Cisco ASR 9000 Series Page 225 Command Reference Manual Download | Manualshive

Page: 225 / 1138

background image

error-disable recovery cause

To configure an interval for the system to bring the interface out of the error-disabled state and retry coming
up, use the

error-disable recovery cause

command. To revert to the defaults, use the

no

form of this command.

error-disable recovery cause

{

cluster-udld| link-oam-capabilities-conflict| link-oam-critical-event|

link-oam-discovery-timeout| link-oam-dying-gasp| link-oam-link-fault| link-oam-miswired|
link-oam-session-down| link-oam-threshold-breached| pvrst-pvid-mismatch| stp-bpdu-guard|
stp-legacy-bpdu| udld-loopback | udld-neighbor-mismatch| udld-timeout| udld-unidirectional

}

interval

Syntax Description

Used when Unidirectional Link Detection (UDLD) is enabled on a
cluster port.

cluster-udld

Used when Ethernet Link OAM configuration conflicts with the peer.

link-oam-capabilities-conflict

Used when a critical event is detected by Ethernet Link OAM.

link-oam-critical-event

Used when an Ethernet Link OAM session fails to come up in time.

link-oam-discovery-timeout

Used when a dying gasp is detected by Ethernet Link OAM.

link-oam-dying-gasp

Used when a unidirectional link is detected by Ethernet Link OAM.

link-oam-link-fault

Used when a mis-wiring is detected with Ethernet Link OAM.

link-oam-miswired

Used when an Ethernet Link OAM session goes down.

link-oam-session-down

Used when a configured error threshold has been breached.

link-oam-threshold-breached

Used when a PVRST BPDU packet is tagged with a VLAN ID which
is different from the VLAN ID on which it was sent.

pvrst-pvid-mismatch

Used when an STP BPDU is received on a port on which BPDU Guard
is configured.

stp-bpdu-guard

Used when a legacy BPDU is received on a port. Only MSTP and
RSTP BPDUs are supported.

stp-legacy-bpdu

Used when UDLD detects that the port is in loopback mode (when its
Tx is directly connected to its Rx).

udld-loopback

Used when mismatched neighbors are detected by UDLD.

udld-neighbor-mismatch

Used when all UDLD neigbors on the link have timed out.

udld-timeout

Used when a link is detected to be unidirectional by UDLD.

udld-unidirectional

Specifies an interval for the recovery period in seconds. The range is
30 to 1000000.

interval

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

205

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

error-disable recovery cause

«
...
223
224
225
226
227
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

MicroTrac Gateway

Brand: YASKAWA Pages: 33

Brand: RTA Pages: 93

Brand: Dusun Pages: 8

SmartNode 5540E Series

Brand: Patton Pages: 77

Brand: DAVIS Pages: 8

Brand: King Pigeon Pages: 52

Brand: King Pigeon Pages: 55

Brand: Omron Pages: 11

Brand: Omron Pages: 78

Brand: Quark-Elec Pages: 7

NetLinx Clear Connect NXB-CCG

Brand: AMX Pages: 3

NetLinx NXB-KNX

Brand: AMX Pages: 2

Brand: Schwaiger Pages: 34

Brand: Elesign Pages: 10

Brand: TVILIGHT Pages: 15

Brand: Universal Remote Control Pages: 26

Brand: SmartPTT Pages: 40

Brand: Shenzhen Seener Wireless Technology Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands