manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual, Page: 304 / 1138

Share
Download
Cisco ASR 9000 Series Command Reference Manual Download Page 304

•

The level of the highest-level MEP on the interface is found. From among the services considered above,
the service in the domain with the lowest level that is higher than the highest MEP level is selected. If
there are no MEPs on the interface, the service in the domain with the lowest level is selected.

•

The MIP auto-creation configuration for the selected service is examined to determine whether a MIP
should be created.

Configuring a MIP auto-creation policy for a service does not guarantee that a MIP will automatically be
created for that service. The policy is only considered if that service is first selected by the algorithm.

Note

Task ID

Operations

Task ID

read, write

ethernet-services

Examples

This example shows how to enable the automatic creation of MIPs for all interfaces in a bridge domain:

RP/0/RSP0/CPU0:router#

configure

RP/0/RSP0/CPU0:router(config)#

ethernet cfm

RP/0/RSP0/CPU0:router(config-cfm)#

domain Domain_One level 1 id string D1

RP/0/RSP0/CPU0:router(config-cfm-dmn)#

service Bridge_Service bridge group BD1 bridge-domain

B1

RP/0/RSP0/CPU0:router(config-cfm-dmn-svc)#

mip auto-create all

Related Commands

Description

Command

domain, on page 201

Enters CFM configuration mode.

ethernet cfm (global), on page 207

service, on page 314

Displays information about errors that are preventing
configured CFM operations from becoming active, as well
as any warnings that have occurred.

show ethernet cfm configuration-errors, on page
322

Displays a list of local maintenance points.

show ethernet cfm local maintenance-points, on
page 330

Displays information about local MEPs.

show ethernet cfm local meps, on page 333

Displays information about maintenance end points
(MEPs) for peer MEPs.

show ethernet cfm peer meps, on page 339

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

284

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

mip auto-create

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments