manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual, Page: 464 / 1138

Share
Download
Cisco ASR 9000 Series Command Reference Manual Download Page 464

frame-relay lmi-t392dce

To set the Local Management Interface (LMI) polling verification timer on the DCE, use the

frame-relay

lmi-t392dce

command in interface configuration mode. To restore the default setting, use the

no

form of this

command.

frame-relay lmi-t392dce seconds

no frame-relay lmi-t392dce seconds

Syntax Description

Polling verification timer, in seconds. The range is from 5 to 30. The default is
15.

seconds

Command Default

The LMI polling verification timer is 15 seconds.

Command Modes

Interface configuration (config-if)

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

frame-relay lmi-t392dce

command is used along with the

frame-relay lmi-t391dte

command to define

the condition that causes the link to be declared down.

The

seconds

value defined in this command must be greater than the polling verification timer defined in the

frame-relay lmi-t391 dte

command.

This

frame-relay lmi-n392dce

command is available on Packet-over-SONET/SDH (POS), serial, and multilink

interfaces.

Task ID

Operations

Task ID

read, write

fr

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

444

Frame Relay Commands on the Cisco ASR 9000 Series Router

frame-relay lmi-t392dce

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments