Cisco ASR 9000 Series Page 1033 Command Reference Manual Download | Manualshive

Page: 1033 / 1138

background image

If the

lnm major-warning

command is run and only the

set

option is configured, the threshold values defined

for the

set

option are also used as the

clear

threshold values. Alternatively, if the

lnm major-warning

command

is run and only the

clear

option is configured, the threshold values defined for the

clear

option are also used

as the

set

threshold values.

Command Modes

T1 configuration

E1 configuration

Command History

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

This command can only be configured on full T1 or E1 channel groups; it is not supported on fractional, or
DS0 links.

The

lnm major-warning

command cannot be configured with the

lnm remove

command

—

they are mutually

exclusive.

The major threshold values must be greater than the values configured in the

lnm minor-warning

command.

LNM supports hierarchical level alarm reporting as defined in the Telcordia (Bellcore) GR-253 standard.
Hierarchical alarm reporting means that whenever a higher alarm is asserted, the lower alarm state is suppressed.
When the high alarm is cleared, the lower alarm will re-assert if the condition still exists.

For LNM, this means that if a major warning threshold is exceeded resulting in a crossed event and alarm
state reached, then a minor warning alarm state is suppressed and placed in stable state. The minor crossed
event also is removed from the bistate log. Only a single crossed event for major warnings will appear in the
bistate log for the controller. When the major warning is cleared, the minor warning alarm is asserted if the
condition still exists.

Task ID

Operation

Task ID

read, write

sonet-sdh

Examples

The following example shows how to enable link noise monitoring on a T1 channel group using the default
values for the set and clear threshold values of 1544 LCVs and 320 PCVs for a duration of 10 seconds:

RP/0/RSP0/CPU0:router(config)#

controller t1 0/6/0/0/1/1

RP/0/RSP0/CPU0:router(config-t1)#

lnm major-warning

The following example shows how to specify set and clear thresholds on an E1 channel group:

RP/0/RSP0/CPU0:router(config)#

controller e1 0/3/0/0/0/1

RP/0/RSP0/CPU0:router(config-e1)#

lnm major-warning set line-code-violation 1500

path-code-violation 100 duration 30

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

1013

T3, E3, T1, E1 Controller Commands on the Cisco ASR 9000 Series Router

lnm major-warning

«
...
1031
1032
1033
1034
1035
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Salus Pages: 2

Brand: versa Pages: 6

VGW VIRTUAL GATEWAY

Brand: Juniper Pages: 6

Flight Stream 110/210

Brand: Garmin Pages: 46

Brand: Nitgen Pages: 66

Brand: AXIOMTEK Pages: 57

Brand: DoorKing Pages: 72

Brand: ioSelect Pages: 160

Brand: King Pigeon Pages: 58

Brand: Peavey Pages: 41

NetLinx NXB-CCG-K

Brand: AMX Pages: 32

Power Xpert Meter 2000

Brand: Eaton Pages: 12

Brand: Technicolor Pages: 103

Brand: enphase Pages: 3

Brand: enphase Pages: 6

ENV-S-AM1-230-60

Brand: enphase Pages: 37

Enphase Envoy-S Metered

Brand: enphase Pages: 49

Brand: ZyXEL Communications Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands