manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

Description

Command

Creates an EOAM profile and enters EOAM configuration mode.

ethernet oam profile, on page 215

Enables Ethernet Link OAM, with default values, on an interface
and enter interface Ethernet OAM configuration mode.

ethernet oam, on page 212

Attaches an Ethernet OAM profile to an interface.

profile (EOAM), on page 299

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

420

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

uni-directional link-fault detection

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

ABB COM600 series Owner'S/Operator'S Manual preview
COM600 series
Brand: ABB Pages: 44
D-Link DG-102S Quick Start Manual preview
DG-102S
Brand: D-Link Pages: 8
D-Link DG-102S Quick Install Manual preview
DG-102S
Brand: D-Link Pages: 12
ABB ARR600 Quick Start Manual preview
ARR600
Brand: ABB Pages: 4
PAC 512 Quick Start Manual preview
512
Brand: PAC Pages: 20
H3C Voice Gateway H3C VG 10-10 Safety Manual preview
Voice Gateway H3C VG 10-10
Brand: H3C Pages: 31
H3C SR6602-I AI Series Installation Manual preview
SR6602-I AI Series
Brand: H3C Pages: 80
H3C SR6602-I AI Series Hardware Information preview
SR6602-I AI Series
Brand: H3C Pages: 33
H3C SecPath M9000 Series Quick Manual preview
SecPath M9000 Series
Brand: H3C Pages: 4
H3C SecPath M9000 Series Installation, Quick Start preview
SecPath M9000 Series
Brand: H3C Pages: 15
H3C MSR3610-I Series Installation, Quick Start preview
MSR3610-I Series
Brand: H3C Pages: 5
H3C SecPath M9000 Series Compliance And Safety Manual preview
SecPath M9000 Series
Brand: H3C Pages: 57
XAVI Technologies Corp. X8824r+ User Manual preview
X8824r+
Brand: XAVI Technologies Corp. Pages: 51
Bivocom TG452 Series User Manual preview
TG452 Series
Brand: Bivocom Pages: 49
Valcom PagePro VIP-204A Quick Start Manual preview
PagePro VIP-204A
Brand: Valcom Pages: 4
Synway SBO500 SBO Series User Manual preview
SBO500 SBO Series
Brand: Synway Pages: 72
Eaton 415U-2 Installation Manual preview
415U-2
Brand: Eaton Pages: 2
Datapulse Intuition 1000 Operator Training Manual preview
Intuition 1000
Brand: Datapulse Pages: 26

Brands by name

Popular brands

Load more brands