manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual, Page: 218 / 1138

Share
Download
Cisco ASR 9000 Series Command Reference Manual Download Page 218

RP/0/RSP0/CPU0:May 29 14:15:39.621 : cfmd[150]: PKT-RX:

CCM: Port status: Up, interface

status Up
RP/0/RSP0/CPU0:May 29 14:15:39.622 : cfmd[150]: PKT-RX:

Raw Frame:

RP/0/RSP0/CPU0:May 29 14:15:39.622 : cfmd[150]: PKT-RX:

0x40010546 00000001 00100404

646F6D34 02047365 72340000 00000000 00000000
RP/0/RSP0/CPU0:May 29 14:15:39.622 : cfmd[150]: PKT-RX:

0x00000000 00000000 00000000

00000000 00000000 00000000 00000000 00000000
RP/0/RSP0/CPU0:May 29 14:15:39.622 : cfmd[150]: PKT-RX:

0x00000000 00000000 00000200

01020400 01010100 05030768 707200
RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX: GigabitEthernet0/1/0/0 egress: CCM

packet sent at level 2 for domain foo, service foo: length 91, src MAC 0001.0203.0400, dst

MAC 0180.c200.0032

RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

CCM: Level 2, opcode CCM, version

0, RDI bit set, interval 10s, seq. num 16, remote MEP ID 1, flags 0x85, first TLV offset

70, 0 unknown TLVs
RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

CCM: MAID: MDID String 'foo',

SMAN String 'foo'
RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

CCM: Sender ID: Chassis ID Local

'ios', Mgmt Addr <none>

RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

CCM: Port status: Up, interface

status Up
RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

Raw Frame:

RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

0x40018546 00000010 00010403

666F6F02 03666F6F 00000000 00000000 00000000
RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

0x00000000 00000000 00000000

00000000 00000000 00000000 00000000 00000000
RP/0/RSP0/CPU0:May 29 14:15:43.625 : cfmd[150]: PKT-TX:

0x00000000 00000000 00000200

01020400 01010100 05030769 6F7300

Related Commands

Description

Command

Logs debug messages about CFM state machines and
protocol events.

debug ethernet cfm protocol-state, on page 199

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

198

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

debug ethernet cfm packets

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments