manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

Task ID

Operations

Task ID

read, write

hdlc

Examples

The following example shows how to configure keepalives for 3 seconds on serial interface 0/7/0/1:

RP/0/RSP0/CPU0:router(config)#

interface serial 0/7/0/1

RP/0/RSP0/CPU0:router(config-if)#

keepalive 3

Related Commands

Description

Command

Displays statistics for all interfaces configured on the router or for
a specific node.

show interfaces, on page 516

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

796

Serial Interface Commands on the Cisco ASR 9000 Series Router

keepalive (serial)

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

ICP DAS USA HRT-711 User Manual preview
HRT-711
Brand: ICP DAS USA Pages: 96
ICP DAS USA GW-7828 User Manual preview
GW-7828
Brand: ICP DAS USA Pages: 38
ICP DAS USA GW-2139M User Manual preview
GW-2139M
Brand: ICP DAS USA Pages: 17
ICP DAS USA DNP-211 Quick Start preview
DNP-211
Brand: ICP DAS USA Pages: 4
ICP DAS USA DGW-521 Quick Start Manual preview
DGW-521
Brand: ICP DAS USA Pages: 8
Banner SureCross Performance FlexPower DX80G9M2S-P7 Manual preview
SureCross Performance FlexPower DX80G9M2S-P7
Brand: Banner Pages: 10
Epygi QUADRO E1 Administrator'S Manual preview
QUADRO E1
Brand: Epygi Pages: 87
ETC Response Analog IO Gateway Setup Manual preview
Response Analog IO Gateway
Brand: ETC Pages: 4
Watchguard Firebox X Core 1250e Firebox X Peak 5500e Quick Start Manual preview
Firebox X Core 1250e Firebox X Peak 5500e
Brand: Watchguard Pages: 10
Intermatic ET9500 Installation Instructions Manual preview
ET9500
Brand: Intermatic Pages: 6
Arrive AirPoint 2011-BYMG Installation Manuals preview
AirPoint 2011-BYMG
Brand: Arrive Pages: 2
schmalenberger FLUVO 27143 Operator'S Manual preview
FLUVO 27143
Brand: schmalenberger Pages: 28
2Wire 2701HG Series Installation Manual preview
2701HG Series
Brand: 2Wire Pages: 132
Technicolor MediaAccess TG589vn Setup And User Manual preview
MediaAccess TG589vn
Brand: Technicolor Pages: 106
Technicolor TG788v v3 Setup And User Manual preview
TG788v v3
Brand: Technicolor Pages: 82
Technicolor DWA0120 Setup And User Manual preview
DWA0120
Brand: Technicolor Pages: 81
YX YX 16-128 User Manual preview
YX 16-128
Brand: YX Pages: 51
YX MOIP 16-128 User Manual preview
MOIP 16-128
Brand: YX Pages: 54

Brands by name

Popular brands

Load more brands