Cisco ASR 9000 Series Page 74 Command Reference Manual Download

Page: 74 / 1138

proactive trigger window

To configure the trigger window (in milliseconds) in which Fast Re-Route may be triggered, use the

proactive

trigger window

command in DWDM configuration mode. To remove the trigger window, use the no form

of this command.

proactive trigger window window

no proactive trigger window window

Syntax Description

The length of time (in milliseconds) of the window in which FEC-FRR may be
triggered. The range is 10 to 10000.

window

Command Default

No default behavior or values

Command Modes

DWDM configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Support for

proactive trigger window

command was included on these

Modular Port Adaptors(MPAs):

•

A9K-MPA-2X40GE

•

A9K-MPA-1X40GE

Release 4.2.3

Usage Guidelines

The proactive feature is used to trigger Forward Error Correction-Fast Re-Route (FEC-FRR).

The

proactive trigger window

command is supported on the legacy line cards but does not function on

the A9K-8X100GE-SE line cards though it is supported on them.

Note

To see the proactive status, use the

show controller dwdm proactive status

command.

Task ID

Operations

Task ID

read, write

dwdm

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

proactive trigger window

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands