Cisco ASR 9000 Series Page 1075 Command Reference Manual Download | Manualshive

Page: 1075 / 1138

background image

◦

slot

—

Physical slot number of the line card or SIP.

◦

module

—

Module number or subslot (for a SPA). A physical layer interface module (PLIM) is

always 0.

◦

port

—

Physical port number of the interface.

◦

T3num

—

T3 controller number.

•

If specifying a virtual interface, the number range varies, depending on interface type.

Task ID

Operations

Task ID

read

interface

Examples

The following example shows sample output from the

show controllers t3

command using the

brief

keyword

for a single T3 port:

RP/0/RSP0/CPU0:router#

show controllers t3 0/4/2/0/1 brief

T3 0/4/2/0 is up

No alarms detected.
mode: serial
MDL transmission is disabled

EIC: , LIC: , FIC: , UNIT:

Path FI:
Idle Signal PORT_NO:
Test Signal GEN_NO:

FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Internal
Alarm Soaking Interval:

Alarm Declaring= 2500 msec
Alarm clearing = 10000 msec

BERT test result (not running)

Test Pattern : Not Configured, Status : not running, Sync Detected : 0
Interval : 1 minute(s), Time Remain : 0 (ms)
Bit Errors (since BERT started): 0 bits,
Bits Received (since BERT started): 0 Kbits
Bit Errors (since last sync): 0 bits
Bits Received (since last sync): 0 Kbits

Table 62: show controllers t3 brief Field Descriptions

Description

Field

T3 channel is operating. The channel state can be up,
down, or administratively down. Loopback conditions
are shown by (Locally Looped) or (Remotely
Looped).

T3 0/4/2/0/1 is up

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

1055

T3, E3, T1, E1 Controller Commands on the Cisco ASR 9000 Series Router

show controllers t3

«
...
1073
1074
1075
1076
1077
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

PathBuilder S200 Series

Brand: 3Com Pages: 31

OfficeConnect 3C855

Brand: 3Com Pages: 3

OfficeConnect 3C855

Brand: 3Com Pages: 4

SentryPlus Alert

Brand: Watts Pages: 12

Brand: RTA Pages: 66

Brand: Elvaco Pages: 2

Intesis IN701-KNX Series

Brand: HMS Networks Pages: 48

Brand: UfiSpace Pages: 14

Brand: Rath Pages: 2

Brand: Microhard Systems Pages: 186

Brand: Zenitel Pages: 14

Brand: CHIYU Pages: 38

Brand: ATX Pages: 84

Brand: 4IPNET Pages: 12

Brand: Planet Pages: 2

XMG3927-B 0A Series

Brand: ZyXEL Communications Pages: 2

Brand: Divebiss Pages: 45

SmartLINK Ei1000G

Brand: Ei Electronics Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands