Cisco ASR 9000 Series Page 68 Command Reference Manual Download | Manualshive

Page: 68 / 1138

background image

proactive revert threshold

To configure the revert threshold to trigger reverting from the Forward Error Correction-Fast Re-Route
(FEC-FRR) route back to the original route, use the

proactive revert threshold

command in DWDM

configuration mode. To remove the revert threshold, use the no form of this command.

proactive revert threshold x-coefficient y-power

no proactive revert threshold x-coefficient y-power

Syntax Description

Bit error rate coefficient (x of xE-y) . The range is 1 to 9. Default is 1.

x-coefficient

Bit error rate exponent (y of xE-y). The range is 3 to 9.

y-power

Command Default

No default behavior or values

Command Modes

DWDM configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Support for

proactive revert threshold

command was included on these

Modular Port Adaptors(MPAs):

•

A9K-MPA-2X40GE

•

A9K-MPA-1X40GE

Release 4.2.3

Usage Guidelines

The proactive feature is used to trigger Forward Error Correction-Fast Re-Route (FEC-FRR).

The

proactive revert threshold

command is supported on the legacy line cards but does not function on

the A9K-8X100GE-SE line cards though it is supported on them.

Note

To see the proactive status, use the

show controller dwdm proactive status

command.

Task ID

Operations

Task ID

read, write

dwdm

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

48

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

proactive revert threshold

«
...
66
67
68
69
70
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: ABB Pages: 44

Brand: FACTBIRD Pages: 2

Fibre to the Curb

Brand: NBN Pages: 9

Intesis IN701-KNX Series

Brand: HMS Networks Pages: 48

Brand: Dragino Pages: 61

Brand: IPitomy Pages: 4

Brand: Alpha Technologies Pages: 25

Brand: THOMSON Pages: 54

Brand: THOMSON Pages: 74

Brand: Netphonic Pages: 36

Cayman 3500 Series

Brand: Netopia Pages: 2

Brand: Netopia Pages: 2

NETSCAPE DIRECTORY SERVER 7.0

Brand: Netscape Pages: 178

Brand: engelmann Pages: 23

Brand: engelmann Pages: 24

Brand: Fanvil Pages: 48

Brand: Gardena Pages: 29

Brand: ZyXEL Communications Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands