Chino KP 2000 Series Instructions Manual Download Page 68

Page: 68 / 144

- 65 -

・

SV section of PID number 9 is out of scope.

・

Confirm the SV section and do the settings again.

10.

・

L is exceeding H.

・

Confirm L/H and do the settings again.

11.

・

Z is exceeding S.

・

Confirm Z/S and do the settings again.

12.

・

Linear range is exceeding the scope of measurement

range.

・

Confirm the measurement range and do the settings again.

13.

・

F.B. tuning is not starting as the status is not RESET status.

・

Start F.B. tuning after making the status as RESET.

14.

・

As pattern selection system or program drive system has

selected exterior, operation cannot be done by front key.

・

When doing the operation by front key, change the pattern

selection system.

15.

・

Operation cannot be started as there is an error in step

repetition setting.

・

Start the operation after reconfirming the settings.

16.

・

Control algorism is not changed because of program

operating.

・

Change the control algorism after stopping the program

operating.

17.

・

Time is not changing as status is not RESET status.

・

Change the time after changing the status to RESET.

Summary of Contents for KP 2000 Series

















































































































































Search results

Summary of Contents for KP 2000 Series

Reviews:

Related manuals for KP 2000 Series

Brands by name

Popular brands

Chino KP 2000 Series, Instructions Manual

Search results

Summary of Contents for KP 2000 Series

Reviews:

Related manuals for KP 2000 Series

Brands by name

Popular brands