manualshive.com logo in svg

Chino KP 2000 Series, Instructions Manual

Share
Download
Chino KP 2000 Series Instructions Manual Download Page 122

 

- 119 -

13. Trouble shooting

 

 

Condition 

Items to be confirmed 

1. There is an error in PV   

or PV is not stable 

・

Confirm that there is no problem in the wiring with the sensor. 

・

For thermocouple, confirm that wiring is done till the terminal screw by 

using thermocouple and compensation lead wire. 

・

Confirm that the terminal screws are tightened properly. 

・

Confirm that sensor signal is not connected in parallel with other 

instrument. 

・

Confirm that protective elements etc are connected to sensor signal 

and the impedance does not become high. 

・

Confirm that there is no problem in output specifications (impedance 

etc.) and output signal of sensor itself. 

・

Confirm that ground terminal is connected to good quality protective 

ground. 

・

Confirm that there is no noise. 

・

Confirm that there is no problem in the environment and atmosphere 

(surrounding temperature, wind etc.) 

・

Confirm that set contents of various parameters (Measurement range, 

sensor correction, customer scale calibration etc) are correct. 

 

2. PV display becomes   
'¯ ¯ ¯ ¯ ¯'. 

・

It indicates excessive input or higher limit burn out for measurement 

range. Confirm the sensor signal. 

 

3. PV display becomes   
'_ _ _ _ _'. 

・

It indicates very little input or lower limit burn out for measurement 

range. Confirm the sensor signal. 

 

4. Control is not stable. 

・

Confirm that there is no problem with the wiring of the actuator. 

・

Confirm that the terminal screw is tightened properly. 

・

Confirm that there is no noise. 

・

Confirm that the set contents of various parameters (PID, output limiter 

etc.) are correct. 

 

Ú

 Regarding controllability, it is necessary to do the design/adjustment 

not only in just the controller but in the entire system of the final 
product. If the controllability does not improve even on adjusting the 
set contents of various parameters (PID etc.) of the controller, 
consult the designer of this final product. 

 

5. 'ERR' of status display lights. 

・

It indicated abnormality in taking the input. In addition to chances of 

abnormality in the internal circuit of the controller, it might be adversely 
affected by noise also, hence confirm that there is no noise. 

 

6. Cause unclear however 

operation is strange 

・

Confirm that the contents of various parameters are correct. 

・

Even then if the operation of the controller is strange, initialize the set 

contents. Do all the settings again and confirm that there is no 
problem in it. 

 

Summary of Contents for KP 2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands