manualshive.com logo in svg

Chino KP 2000 Series, Instructions Manual

Share
Download
Chino KP 2000 Series Instructions Manual Download Page 46

 

- 43 -

 

7-6. Mode 4

 

 

Mode 4 performs the setting related to output. 

 

Settings screen 

Description of the screen 

1. Mode screen 

 

 

 

 [Lock Status] 

 

 

  [Display OFF status] 

 

①

 Mode 4 screen.

 

 

②

 

By clicking the 

･

 key, 'Lock' and 'NoDisp' is displayed.

 

 

 

③

 For mode 4 settings screen, if setting change is to be prohibited 

select 'Lock'.

 

④

 When doing the settings by communications, set all the mode 

screens to 'Lock'.

 

 

⑤

 When settings screen of mode 4 is not displayed, select 'NoDisp'.

 

 

2. Output limiter 8 types 

 

 

 
[Output scaling specifications] 

 

 

Ú

 Option 

Output limiter 

①

 

Set 8 types of output limiters. 

②

 

Set lower limit of output limiter in 'L' , and upper limit of output limiter 
in 'H'.

 

③

 

In either of automatic output operation and manual output operation 
the output is within this setting range.

 

④

 

After the settings, it is necessary to set the output limiter number 
that is to be used for each pattern/step in mode 2.

 

Output scaling (Option) 

①

  Set 8 types of output scaling. 

②

  Set lower limit of output scaling in ‘L’, and upper ;limit of output 

scaling in ‘H’. 

③

  In case of automatic output operation, output is scaled within rage 

of this setting, however in case of manual output operation, output 
is not scaled.   

④

  After the setting, set the which output scaling No. is used in each 

pattern /step at mode 2.

 

3. Second output limiter 
 

 

 

 
 [Output scaling specifications] 

 

 

Ú

 Option 

Second output limiter 

①

 

It is displayed in case of output 2 specifications only.

 

②

 

Set the output limiter of output 2 side.

 

③

 

Set lower limit of output limiter in 'L' , and upper limit of output limiter 
in 'H'.

 

④

 

In either of automatic output operation and manual output operation 
the output is within this setting range.

 

Second output scaling (Option) 

①

  It is displayed in case of output 2 specifications only. 

②

  Set the output scaling of output 2 side. 

③

  Set lower limit of output scaling in ‘L’, and upper ;limit of output 

scaling in ‘H’. 

④

  In case of automatic output operation, output is scaled within rage 

of this setting, however in case of manual output operation, output 
is not scaled.

 

 

Summary of Contents for KP 2000 Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands