Chapter 6 - Parameter Description
6-35
APP ExtSetPoint
80 50.0 %
APP Ext Fbk Sel
81 I
APP ExtFbk Unit
82 %
Main-
the alternation mode is enabled and VFD
will alternate auxiliary motors on the VFD output
by run time timer.
APP-67-
the alternation run time timer setting is in
hours. The VFD counts only run time and when it
exceeds
APP-67
and VFD output frequency is
lower than
APP-68
setting, VFD stops the motor,
deactivates its relay, then closes next motor relay
and starts again.
%
)05+ %':
"
1 $! "
9
APP-69
enables an
MMC motor interlock
(disable) feature if it is set to Yes. Any motor Aux
relay can be disabled by corresponding digital input
set to interlock.
?
%
$ 1
%
)34+ : "!
$
!
APP-78
enables
external (2
nd
) PID
control if it is set to Yes. External PID can be used
to process system value (pressure, temperature etc)
and provide output to VFD speed reference, analog
0-10VDC output or set-point of the main PID
control.
%
)35+ : "!
$
> " !
!
APP-79
allows four
reference (set-point)
source selections: I, V1, Pulse and Keypad. Refer to
SET-10 for detailed description.
%
)4*+ : "!
$
)
!
'
APP-80
determines the
external PID set-point
value as a percentage of the maximum feedback
value.
%
)4 + : "!
$
8 9
'"
!
APP-81
allows three
feedback signal source
selections: I, V1 and Pulse. Refer to SET-10 for
detailed description.
%
)4 + : "!
$
8 9 !
!
APP-82
allows
following feedback
signal unit selections: %, PSI, °F, °C, inWC, inM,
Bar, mBar, Pa, kPa and Custom. Refer to SET-22
for detailed description.
%
)4/+ : "!
$
8 9
:
'
'
APP-84
is the external
PID maximum
feedback unit value.
%
)47A43+ : "!
$
)
!6 $)
!
)
H
APP-85, 86, and 87
are the P-Gain, I-Time and D-
Time parameters for external PID setup. Refer to
the description for these parameters settings in
SET-29 ,30 and APP-09.
%
)44645+ : "!
$
' ' # -, !
(
APP-88-
The PID Output High Limit setting.
APP-89-
The PID Output Low Limit setting.
APP interlock
69 No
APP Ext PI Mode
78 No
APP Ext Ref Sel
79 Keypad
APP ExtFbk UnitH
84 100.0 %
APP ExtPID PGain
85 1.0 %
APP ExtPID ITime
86 10.0 sec
APP ExtPID DTime
87 0 ms
APP ExtPID LmtH
88
100.0 %
APP ExtPID LmtL
89
0.0 %
VFD Output to Motors
M1
M2
M3
M4
P-VFD
Line
Power
External
Relays
Motor 4
Motor 3
Motor 2
Motor 1
RLY1
RLY2
RLY3
RLY4
Aux1
Aux 2
Aux 3
Aux 4
Summary of Contents for CI-007-P2
