Burkert 8756 Operating Instructions Manual Download Page 85

Page: 85 / 88

Type 8756

Logistic

english

13.2

Storage

ATTENTION!

Incorrect storage can cause damage to the product.

▶

Close fluid connections with protective caps.

▶

Store the product dry and dust-free in sealed zip lock bags.

▶

Storage temperature: –10...+70 °C.

13.3

Return

No work or tests will be carried out on the product until a
valid Contamination Declaration has been received.

To return a used product, a return number is required.

To return a used product to Bürkert, contact your Bürkert
sales office.

13.4

Disposal

ATTENTION!

Environmental damage that is due to parts contaminated by
fluids.

▶

Dispose of the product and its packaging in an environment-
ally friendly manner.

▶

Comply with applicable environmental and disposal regula-
tions.

Summary of Contents for 8756

























































































Search results

Summary of Contents for 8756

Reviews:

Related manuals for 8756

Brands by name

Popular brands

Burkert 8756, Operating Instructions Manual

Search results

Summary of Contents for 8756

Reviews:

Related manuals for 8756

Brands by name

Popular brands