Burkert 8756 Operating Instructions Manual Download Page 7 | Manualshive

Page: 7 / 88

background image

Type 8756

Safety instructions

english

7

Only use the product for its intended purpose.

2.3

General safety information

The safety instructions do not take into account any contingen-
cies or occurrences that may arise during installation, use and
maintenance of the product. The operating company is respons-
ible for the respect of the local safety regulations including for the
personnel safety.

DANGER!

Risk of injury that is due to pressure in the installation or in the
product.

▶

Before working on the installation or product, cut the pres-
sure. Vent and drain the pipes.

DANGER!

Risk of injury from electric shocks.

▶

Before working on the installation or product, switch off the
power supply. Make sure that nobody can switch the power
supply on.

▶

Observe all applicable accident protection and all applicable
safety regulations for electrical equipment.

DANGER!

Burn hazard and fire hazard that are due to hot surface of the
product.

▶

Do not touch the hot surface with bare hands.

▶

Wear safety gloves to touch the product.

▶

Keep the product away from any highly flammable materials
or fluids.

WARNING!

Risk of injury that is due to escape of the fluid.

Contact with the operating fluid, its reaction products and va-
pours can cause injuries.

Inhaled vapours can be harmful.

▶

Observe all applicable accident protection and all applicable
safety regulations relating to the operating fluid used.

To avoid personal injury, obey the following instructions:

Only operate the product with a filtered fluid.
Make sure that the operating pressure of the product is not
higher than the maximum authorized operating pressure. Refer
to the data sheet of the product on our homepage:

country.burkert.com

.

Only use the product for fluids that are compatible with the
product materials.
Do not make any modifications to the product and do not sub-
ject the product to mechanical stress.

«
...
5
6
7
8
9
...
»

Summary of Contents for 8756

























































































Reviews:

No comments

Related manuals for 8756

Brand: Parker Research Corp Pages: 3

Brand: HANYOUNG NUX Pages: 4

Brand: jenway Pages: 30

Brand: National Meter & Automation Pages: 24

Brand: Lakeshore Pages: 2

Brand: Kamstrup Pages: 4

CP-4900 Micro-GC

Brand: Varian Pages: 7

Brand: Vapotherm Pages: 2

Brand: E Instruments Pages: 144

Brand: Gates Pages: 112

Litemaster Pro L-478DR

Brand: Sekonic Pages: 16

Brand: Agilent Technologies Pages: 198

Brand: Omega Pages: 22

MultiScanner HD800 OneStep

Brand: Zircon Pages: 2

Brand: HERON Pages: 2

Brand: Vector Pages: 8

Brand: Novus Pages: 52

Brand: Rockler Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands