Burkert 8756 Operating Instructions Manual Download Page 84

Page: 84 / 88

Type 8756

Logistic

english

Fluid connections

Fig. 32: Fluid connections, for example internal-threaded connec-
tions

Remove the product.

LOGISTIC

13.1

Transport

ATTENTION!

Transport damage.

If the product is not protected in transport, then the product can
be damaged.

▶

Remove cables, connectors, product-external filters and in-
stallation equipment.

▶

Protect the electrical interfaces with protective plugs.

▶

Clean and vent contaminated products.

▶

Close the fluid connections with protective caps. Protective
caps ensure protection and sealing.

▶

Pack the product in two suitable zip lock bags, to avoid any
contamination during the transport.

▶

Transport the product in an impact-resistant package, protec-
ted from moisture and dirt.

▶

Avoid storage above or below the recommended storage tem-
perature.

Summary of Contents for 8756

























































































Search results

Summary of Contents for 8756

Reviews:

Related manuals for 8756

Brands by name

Popular brands

Burkert 8756, Operating Instructions Manual

Search results

Summary of Contents for 8756

Reviews:

Related manuals for 8756

Brands by name

Popular brands