Burkert 8756 Operating Instructions Manual Download Page 56 | Manualshive

Page: 56 / 88

background image

Type 8756

Setting and operation

english

56

8.5.2

Increase the data transmission
speed

If the data transmission speed is increased, then the product
provides more cyclic process-data.

For example, the actual value of the mass flow rate is available
once every 100 ms by default. If the data transmission-speed is
increased, then the actual value of the mass flow rate is available
once every 10 ms.

If the data transmission-speed is active simultaneously on
several products in the network, then make sure that the bus
load does not exceed 50%.

To increase the data transmission-speed, do the following:

Energise the bus network.
Connect the product to the Bürkert Communicator software.
Refer to chapter:

Connect the product to the Bürkert Com-

municator software [

In the Bürkert Communicator software, move the PC mouse
over the büS-stick symbol in the list of devices. If the bus load
is higher than 45%, then do not increase the data transmis-
sion-speed.
If the bus load is less than or equal to 45%, then the data
transmission-speed can be increased. Do the following pro-
cedure:
In the Bürkert Communicator software, select the product.

The product status indicator flashes.

Go to

General settings

>

Diagnostics

>

Inhibit time

.

To increase the data transmission-speed, click

Set diagnostic

mode

. The function

Inhibit time

switches to

Set to default val-

ues

.

The data transmission-speed is increased.

To go back to the default data transmission-speed, click

Set

to default values

. The function

Inhibit time

switches to

Set

diagnostic mode

.

8.6

Operating modes of an MFC

When energising the product for the first time, the product enters
a short initialization phase and then switches to the normal oper-
ating mode. The normal operating mode is described in chapter:

Normal operating mode (MFC) [

The possible operating modes are described in following table.

Operating mode

Description

Product variant büS/CANopen:

Automatic

Refer to chapter:

ating mode (MFC) [

Product variant Analogue:

Ana-

log set-point value

Refer to chapter:

ating mode (MFC) [

Manual set-point value

Refer to chapter:

source that gives the set-point
value (MFC) [

Stored set-point value

Refer to chapter:

source that gives the set-point
value (MFC) [

«
...
54
55
56
57
58
...
»

Summary of Contents for 8756

























































































Reviews:

No comments

Related manuals for 8756

Brand: TANDBERG Pages: 53

Brand: E Instruments Pages: 144

Brand: Flytec Pages: 2

Brand: Energic Plus Pages: 12

AccuPoint 2 ATP

Brand: Neogen Corporation Pages: 16

Brand: CAS Corporation Pages: 20

Brand: Primes Pages: 56

Brand: Ratek Pages: 24

Brand: Oldham Pages: 106

NOVAplus biogas

Brand: mru Pages: 78

Brand: Hach Pages: 4

Brand: Novus Pages: 52

Brand: Rockler Pages: 4

Brand: Oldham Pages: 80

Brand: INTERSPIRO Pages: 76

Brand: Net2Edge Pages: 37

Brand: Vaisala Pages: 96

GenTwo PMA1000V2.4

Brand: M&C Pages: 110

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands