Burkert 8756 Operating Instructions Manual Download Page 53 | Manualshive

Page: 53 / 88

background image

Type 8756

Setting and operation

english

53

8.3

Tools for doing the settings

The MassFlowCommunicator is another PC software that
is not compatible with the product. You cannot use the
MassFlowCommunicator software to configure or operate
the product.

Settings can be made with the Type 8920 Bürkert Communicator
software.

To connect the product to the Bürkert Communicator soft-
ware, refer to chapter:

Connect the product to the Bürkert

Communicator software [

For general information about the Bürkert Communicator soft-
ware, refer to the Type 8920 Operating Instructions.

8.4

Connect the product to the Bürkert
Communicator software

8.4.1

Product variant büS /CANopen

To do the settings with the Type 8920 Bürkert Communicator
software, do the following steps:

Buy the USB-büS-interface set with article number 00772426
from Bürkert. Refer to following figure.

büS stick with termination-
resistance switch

Fig. 25: USB-büS-interface set with article number 00772426

Download the latest version of the Type 8920 Bürkert Commu-
nicator software from

country.burkert.com

During installation, the büS stick must not be inserted at the
PC. Install the Bürkert Communicator software on a PC. Obey
the installation recommendations given in the USBbüS- inter-
face set.

The following figure shows the electrical connection parts that are
used from the USB-büS-interface set.

«
...
51
52
53
54
55
...
»

Summary of Contents for 8756

























































































Reviews:

No comments

Related manuals for 8756

Power Xpert PXM 4000

Brand: Eaton Pages: 28

Brand: IFR Pages: 46

Brand: WATERGUARD Pages: 2

Brand: JENCO Pages: 13

Smart Air Quality Monitor

Brand: Lennox Pages: 28

Brand: Roland Pages: 96

Brand: pts Diagnostics Pages: 2

LeakTracker OIL-GLO ULTRA

Brand: Spectroline Pages: 12

Amplitude T Series

Brand: OTOVATION Pages: 15

Brand: IS Technologies Pages: 21

Brand: Mityvac Pages: 24

EnviroAlert EA200

Brand: Winland Pages: 3

MJK MagFlux Series

Brand: Xylem Pages: 179

Brand: jacarta Pages: 44

Brand: Bushnell Pages: 64

Brand: Canary Pages: 19

Pulse sens'O Atex zone 1 50-70-123

Brand: WATTECO Pages: 12

Brand: Astute Medical Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands