background image

Inch (SAE) and Metric Fasteners

M1.1

F-code

Section

C-code

Version no

T-code

001

© BT Products

25

Service Manual

1997-09-24

3. Strength Identification

The  most common property classes for metric fasteners are
8.8 and 10.9. The property class is marked with a number on
the head of the cap screw or on a nut. Property classes less
then 8.8 are often not marked. Grades for inch bolts go from 2
to 8. Grade 2 fasteners normally do not have marks. The
following tables show the marks that identify the grades and
property classes for different fasteners.

When fasteners must be replaced the new
fasteners must be of the same strength or
greater than the original fasteners. The
new  fasteners must also be  the  correct
size.

WARNING

NOTE! Identification marks are according to bolt

strength.  The  higher  the  number, or the
increase in the number of marks, indicates
increased bolt strength.

Return

Summary of Contents for OE35













































































































































































































































































































































Reviews: