BT LPE200 Service Manual Download Page 65

Page: 65 / 154

Electrical System – 5000 LWE 180/200 LPE 200

Error codes

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

9- 27

Code

E141

Description

Software problem.

Possible error
cause

Fault on the internal monitoring (tiller arm head),
incorrect software or circuit board.

Action

Restart the machine.

Download the program again.

Replace the electronic card

Code

E150

Description

Fault in the data communication.

Possible error
cause

Break on the CAN cable.

Action

Check the 119 and 120 cables and their contacts.

Replace travel regulator.

Code

E151

Description

Tx error in data communication.

Possible error
cause

Travel regulator not responding.

Action

Check 119 and 120 cables and the connec-
tions on the travel regulator.

Replace travel regulator.

Code

E157

Description

Bus shut off.

Possible error
cause

CAN bus problem.

Action

Check 119 and 120 cables and the connec-
tions on the travel regulator.

Replace travel regulator.

Replace the electronic card

Summary of Contents for LPE200



























































































































































Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands

BT LPE200, Service Manual

Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands