BT LPE200 Service Manual Download Page 61

Page: 61 / 154

Electrical System – 5000 LWE 180/200 LPE 200

Error codes

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

9- 23

Code

E101

Description

Travel regulator does not correspond with the type
of truck

Possible error
cause

Incorrect travel regulator or electronic card has
been installed. The truck has a built-in control
function that checks to ensure the wrong combina-
tion of travel regulator and electronic card has not
been installed.

Action

Check travel regulator and electronic card.

Code

E104

Description

Switch-transistor to brake is short-circuited

Possible error
cause

Error in the travel regulator, output. A1/3.
Incorrect value on parameter 22

Action

Check cabling and contacts. Measure Ohms on
the magnet coil (Y1) for the brake.

Value 13-15 ohm.
Check parameter 22

Summary of Contents for LPE200



























































































































































Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands

BT LPE200, Service Manual

Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands