manualshive.com logo in svg

BT LPE200, Service Manual

The BT LPE200 Service Manual is readily available for free download on manualshive.com. This comprehensive manual provides detailed instructions and troubleshooting techniques for efficiently operating and maintaining your BT LPE200. Accessible in a user-friendly format, it ensures seamless product utilization, offering immense value to users seeking a reliable reference guide.

Share
Download
background image

9-  26

Service Guide 

LWE180, LWE200, LPE200, LPE240

© BT Europe AB

Electrical System – 5000 LWE 180/200 LPE 200

Error codes

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497 

723984-

2005-05-11

225553-040

Code

E108

Description

Contactor K10 does not open.

Possible error 
cause

Main contactor points welded.
Short circuit in the travel regulator’s output A1/4.

Action

1.

Check that the contactor’s contact points are 
not welded together.

2.

Check that the R1 resistor is not short-
circuited.

3.

If the contact points are OK, but the contactor 
engaged, check cable 64 and the travel regu-
lator’s output A1/4.

Code

E110

Description

System error.

Possible error 
cause

Temporary error/error in the travel regulator.

Action

1.

Restart the machine.

2.

Replace travel regulator.

Code

E140

Description

Error in control total.

Possible error 
cause

Fault on the internal micro-monitoring (tiller arm 
head), incorrect software or circuit board.

Summary of Contents for LPE200



























































































































































Reviews:

No comments

Related manuals for LPE200

Still RCD40 Original Instructions Manual preview
RCD40
Brand: Still Pages: 170

Brands by name

Popular brands

Load more brands