BT LPE200 Service Manual Download Page 109

Page: 109 / 154

Electrical systems – 5000 LPE 240

Error codes

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

10- 17

Code

C42

Description

Warning of high battery voltage

Possible error
cause

Battery voltage > 33 volt.
Energy return feed to battery during motor braking
with a fully-charged battery.

Action

The fault disappears after a few lifts, once the
battery has been run down slightly.

Check the cabling, the battery contact and the
contact points on main contactor K10.

Code

C43

Description

The travel regulator shuts off due to excess or
subnormal temperature.

Possible error
cause

Too intensive operation or ambient temperature
too cold.
Error in the travel regulator.

Temperature levels below -25

C or above +85

reduce running speed.

Action

Check that the M12 fan is functioning.

(Applies to P 24)

Check that the travel regulator is installed with
good contact with the chassis.

Summary of Contents for LPE200



























































































































































Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands

BT LPE200, Service Manual

Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands