BT LPE200 Service Manual Download Page 118

Page: 118 / 154

10- 26

Service Guide

LWE180, LWE200, LPE200, LPE240

Electrical systems – 5000 LPE 240

Parameters

T-code

Valid from serial number

Date

Order number

660, 661, 662, 497

723984-

2005-05-11

225553-040

10.6.2 Parameter description

Parameter 1

Possibility to adjust the speed in the low speed range (when the safety
gates are not used).

Parameter 2

Possibility to adjust the speed in the high speed range (when the safety
gates are used).

Parameter 3

The lower value of the parameter the longer time it takes to accelerate
the truck to top speed.

Parameter 4

Defines motor brake force when lever (L1) goes to neutral position.The
lower value of parameter the longer time to reduce speed.

Parameter 5

The time until the truck will be switched off when a key pad is used.
Time is counted from when the latest power consumer is used.

Value = 0 gives 4 hours.

Summary of Contents for LPE200



























































































































































Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands

BT LPE200, Service Manual

Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands