BT LPE200 Service Manual Download Page 139

Page: 139 / 154

Electrical systems – 5000 LPE 240

Diagnostic and troubleshooting

Order number

Date

Valid from serial number

T-code

225553-040

2005-05-11

723984-

660, 661, 662, 497

Service Guide

LWE180, LWE200, LPE200, LPE240

10- 47

10.9 Diagnostic and troubleshooting

10.9.1 Error codes and troubleshooting

The table below depicts the error codes that may be shown by the STA-
TUS LED or read using the handheld terminal.

STATUS LED

Handheld ter-
minal display

Explanation

Possible cause

LED off

No voltage or
defective regulator

Burnt fuse, bad contact, not con-
nected, defective regulator

LED on

Defective regulator

1,1

¤ ¤

CURRENT
SHUNT FAULT

Built-in current
shunt defective

Armature current sensor fault in motor
controller.

1,2

¤ ¤¤

HW FAILSAFE

Power amplifier
CAN-timeout

Motor controller reports unexpected
loss of data flow from tiller head

1,3

¤ ¤¤¤

M- SHORTED

Internal M- short to
B-

Problem with switch transistor in arma-
ture circuit inside motor controller

3,1

¤¤¤ ¤

CONT COIL/FLD
SHORT

Too high current for
contactor feeding
or shorted field
winding

Attempt to drive more current than
specified from outputs.
Problem to regulate field currrent.
Internal controller fault.

3,3

¤¤¤ ¤¤¤

FIELD OPEN

Open field winding

Shuntfield open, harness broken,
motor controller defect.

4,1

¤¤¤¤ ¤

LOW BATTERY
VOLTAGE

Low battery voltage

1. Battery voltage <17 volts

2. Corroded battery terminals

3. Loose battery or regulator connec-
tions

4,2

¤¤¤¤ ¤¤

OVERVOLTAGE

Overvoltage

1. Battery voltage > 33 volts

4,3

¤¤¤¤ ¤¤¤

THERMAL

CUTBACK

Over-/under-tem-
perature reduction

1. Temp. >85

C or < - 25

2. Truck overloaded

3. Wrong installation of transistor

regulator

4. Operation under extreme conditions

MODEL

STATUS

SERIAL

VOLTAGE

CURRENT

Summary of Contents for LPE200



























































































































































Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands

BT LPE200, Service Manual

Search results

Summary of Contents for LPE200

Reviews:

Related manuals for LPE200

Brands by name

Popular brands