Brovision WH-N5204-P4 User Manual Download Page 99

Page: 99 / 222

User Manual of Network Video Recorder

Figure 6. 20

Interface of Playback by Log

6.1.7

Playing Back External File

Purpose:

Perform the following steps to look up and play back files in the external devices.

Steps:

Enter Playback interface.

Menu>Playback

Select the

External File

in the drop-down list on the top-left side.

The files are listed in the right-side list.

You can click the

button to refresh the file list.

Select and click the

button to play back it. And you can adjust the playback speed by clicking

and

Figure 6. 21

Interface of External File Playback

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands