Brovision WH-N5204-P4 User Manual Download Page 52

Page: 52 / 222

User Manual of Network Video Recorder

4.2

Setting PTZ Presets, Patrols & Patterns

Before you start:

Please make sure that the presets, patrols and patterns should be supported by PTZ protocols.

4.2.1

Customizing Presets

Purpose:

Follow the steps to set the Preset location which you want the PTZ camera to point to when an event takes place.

Steps:

Enter the PTZ Control interface.

Menu>Camera>PTZ>More Settings

Figure 4. 2

PTZ- More Settings

Use the directional button to wheel the camera to the location where you want to set preset.

Click the round icon before

Save Preset

Click the preset number to save the preset.

Repeat the steps2-4 to save more presets. If the number of the presets you want to save is more than 17, you can

click […] and choose the available numbers.

Figure 4. 3

More Presets

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands