Brovision WH-N5204-P4 User Manual Download Page 179

Page: 179 / 222

User Manual of Network Video Recorder

178

10.5

Configuring Quota Mode

Purpose:

Each camera can be configured with allocated quota for the storage of recorded files or captured pictures.

Steps:

Enter the Storage Mode interface.

Menu > HDD > Advanced

Set the

Mode

to Quota, as shown in Figure 10. 18.

The NVR must be rebooted to enable the changes to take effect.

Figure 10. 18

Storage Mode Settings Interface

Select a camera for which you want to configure quota.

Enter the storage capacity in the text fields of

Max. Record Capacity (GB)

and

Max. Picture Capacity

(GB)

, as shown in Figure 10. 19.

Figure 10. 19

Configure Record/Picture Quota

You can copy the quota settings of the current camera to other cameras if required. Click the

Copy

button to

enter the Copy Camera menu, as shown in Figure 10. 20.

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Brands by name

Popular brands