Brovision WH-N5204-P4 User Manual Download Page 3

Page: 3 / 222

User Manual of Network Video Recorder

Preventive and Cautionary Tips

Before connecting and operating your device, please be advised of the following tips:

•

Ensure unit is installed in a well-ventilated, dust-free environment.

•

Unit is designed for indoor use only.

•

Keep all liquids away from the device.

•

Ensure environmental conditions meet factory specifications.

•

Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it

may cause damage to the sensitive electronics within the unit.

•

Use the device in conjunction with an UPS if possible.

•

Power down the unit before connecting and disconnecting accessories and peripherals.

•

A factory recommended HDD should be used for this device.

•

Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or

equivalent type only. Dispose of used batteries according to the instructions provided by the battery

manufacturer.

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Brands by name

Popular brands