manualshive.com logo in svg

Brovision WH-N5204-P4, User Manual

Share
Download
Brovision WH-N5204-P4 User Manual Download Page 171

User Manual of Network Video Recorder 

 

170 

10.1

 

Initializing HDDs 

Purpose: 

A newly installed hard disk drive (HDD) must be initialized before it can be used with your NVR.

 

 

A message box pops up when the NVR starts up if there exits any uninitialized HDD. 

 

Figure 10. 1

 

Message Box of Uninitialized HDD 

 

Click 

Yes

 button to initialize it immediately or you can perform the following steps to initialize the HDD. 

Steps: 

1.

 

Enter the HDD Information interface. 

Menu > HDD> General 

 

Figure 10. 2

 

HDD Information Interface 

 

2.

 

Select HDD to be initialized. 

3.

 

Click the 

Init

 button. 

 

Figure 10. 3

 

Confirm Initialization 

 

4.

 

Select the 

OK

 button to start initialization.   

 

Figure 10. 4

 

Status changes to Initializing 

 

Summary of Contents for WH-N5204-P4































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands