Brovision WH-N5204-P4 User Manual Download Page 190

Page: 190 / 222

User Manual of Network Video Recorder

189

11.2

Configuring Privacy Mask

Purpose:

You are allowed to configure the four-sided privacy mask zones that cannot be viewed by the operator. The privacy

mask can prevent certain surveillance areas to be viewed or recorded.

Steps:

Enter the Privacy Mask Settings interface.

Menu > Camera >Privacy Mask

Select the camera to set privacy mask.

Click the checkbox of

Enable Privacy Mask

to enable this feature.

Figure 11. 2

Privacy Mask Settings Interface

Use the mouse to draw a zone on the window. The zones will be marked with different frame colors.

Up to 4 privacy masks zones can be configured and the size of each area can be adjusted.

The configured privacy mask zones on the window can be cleared by clicking the corresponding Clear

Zone1-4 icons on the right side of the window, or click

Clear All

to clear all zones.

Figure 11. 3

Set Privacy Mask Area

Click the

Apply

button to save the settings.

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Brands by name

Popular brands