Brovision WH-N5204-P4 User Manual Download Page 141

Page: 141 / 222

User Manual of Network Video Recorder

140

8.6

Handling Exceptions Alarm

Purpose:

Exception settings refer to the handling action of various exceptions, e.g.

•

HDD Full:

The HDD is full.

•

HDD Error:

Writing HDD error or unformatted HDD.

•

Network Disconnected:

Disconnected network cable.

•

IP Conflicted:

Duplicated IP address.

•

Illegal Login:

Incorrect user ID or password.

•

Record/Capture Exception:

No space for saving recorded files or captured images.

•

Hot Spare Exception:

Disconnected with the working device.

•

Array Exception:

Abnormal virtual disks exist under array.

Array Exception is only supported by RAID series NVR.

Steps:

Enter Exception interface of System Configuration and handle various exceptions.

Menu> Configuration> Exceptions

Please refer to

Chapter Setting Alarm Response Actions

for detailed alarm response actions.

Figure 8. 15

Exceptions Setup Interface

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands