Brovision WH-N5204-P4 User Manual Download Page 177

Page: 177 / 222

User Manual of Network Video Recorder

176

Select the Group number for the current HDD.

The default group No. for each HDD is 1.

Click the

button to confirm the settings.

Figure 10. 16

Confirm HDD Group Settings

In the pop-up Attention box, click the

Yes

button to finish the settings.

10.4.2

Setting HDD Property

Purpose:

The HDD property can be set to redundancy, read-only or read/write (R/W). Before setting the HDD property,

please set the storage mode to Group (refer to step1-4 of Chapter Setting HDD Groups ).

A HDD can be set to read-only to prevent important recorded files from being overwritten when the HDD becomes

full in overwrite recording mode.

When the HDD property is set to redundancy, the video can be recorded both onto the redundancy HDD and the

R/W HDD simultaneously so as to ensure high security and reliability of video data.

Steps:

Enter the HDD Information interface.

Menu > HDD> General

Select HDD from the list and click the

icon to enter the Local HDD Settings interface, as shown in

Figure 10. 17.

Figure 10. 17

Set HDD Property

Set the HDD property to R/W, Read-only or Redundancy.

Click the

button to save the settings and exit the interface.

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands