Brovision WH-N5204-P4 User Manual Download Page 208

Page: 208 / 222

User Manual of Network Video Recorder

207

13.4

Configuring More Settings for Device

Parameters

Steps:

Enter the General Settings interface.

Menu >Configuration>General

Click the

More Settings

tab to enter the More Settings interface, as shown in Figure 13. 4

Figure 13. 4

More Settings Interface

Configure the following settings:

•

Device Name:

Edit the name of NVR.

•

Device No.:

Edit the serial number of NVR. The Device No. can be set in the range of 1~255, and the

default No. is 255. The number is used for the remote and keyboard control.

•

CVBS Output Brightness:

Adjust the video output brightness.

•

Auto Logout:

Set timeout time for menu inactivity. E.g., when the timeout time is set to

5 Minutes

, then

the system will exit from the current operation menu to live view screen after 5 minutes of menu

inactivity.

•

Enable HDMI/VGA Simultaneous Output:

By default, the video outputs from HDMI and VGA

interfaces can be operated separately. You can set the simultaneous output for the HDMI and VGA by

checking the checkbox of the option.

•

Menu Output Mode:

You can choose the menu display on different video output. There are auto,

HDMI, VGA and Main CVBS selectable.

Click the

Apply

button to save the settings.

Summary of Contents for WH-N5204-P4































































































































































































































Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands

Brovision WH-N5204-P4, User Manual

Search results

Summary of Contents for WH-N5204-P4

Reviews:

Related manuals for WH-N5204-P4

Brands by name

Popular brands