SAFETY
Cooling System
WARNING
To prevent serious injury from hot coolant
and steam,
DO NOT
remove the radiator
cap when the engine is running and/or hot.
Allow the engine and system to cool, and
use caution when removing the radiator cap.
•
Do not operate the engine without the recom-
mended coolant mixture.
•
Add top-up coolant into the recovery tank
NOT
directly to the radiator
•
Ensure that the radiator cap is tight and
secure.
•
If the radiator cap must be removed, stop the
engine and allow the cooling system to cool,
until the cap is cool to the touch. Loosen it
slowly to relieve pressure, before removing
completely.
Battery Service
WARNING
The sulfuric acid in the battery electrolyte is
poisonous. It can cause serious skin burns
and blindness if splashed in the eyes.
CAUTION
Always wear protective glasses/goggles,
and protective clothing and use insulated
tools when working with batteries.
Read, understand, and obey all battery manuf-
acturers instructions and warnings.
Battery posts, terminals and relate accessories
contain lead, lead compounds and chemicals,
wash your hands after handling them.
Avoid Hazards By:
•
Fill/top-up batteries in a well ventilated area.
•
Wearing eye protection and rubber gloves.
•
Avoid breathing fumes.
•
Avoid spilling, splashing or dripping
electrolyte.
•
Follow proper ‘jump-start’ procedure.
If acid is splashed on your person:
•
Flush the affected skin with water.
•
Apply baking soda, or lime, to help neutralize
the acid.
•
Flush your eyes with water for 15 to 30
minutes. Get medical help immediately.
1-06
If acid is swallowed:
•
Do not induce vomiting
•
Drink large quantities of water or milk, but do
not exceed 2 liters (2 Quarts).
•
Get medical help immediately.
Battery Charging
•
Charge batteries in an open well ventilated
area, away from sparks or open flame.
•
Unplug the charger before connecting or
disconnecting the battery.
Jump Starting
•
Check that the Jumper cables are in good
condition.
•
Turn the ignition and all electrical accessories
‘OFF’, on both machines.
•
Position the machine with the ‘charged’
battery close to, but not touching, the
machine with the dead battery, to ensure that
the cables will easily reach.
Connecting the Cables
•
Do not allow the cable clamps to touch any
metal parts except those intended.
•
Never connect the
positive ‘+’
(red) terminal
to the
negative ‘-‘
(black) terminal.
•
Ensure that the cables cannot get caught in
moving engine parts when starting.
•
Connect one end of the
positive ‘+’
(red)
cable to the
positive ‘-‘
terminal on one
battery. Connect the other end to the
positive ‘+’
terminal on the other battery
•
Connect one end of the negative ‘-‘ (black)
cable to the negative ‘-‘ terminal on the
‘charged’ battery. Connect the other end of
the cable
to the engine block
on the
machine with the ‘dead’ battery.
•
Start the machine that has the ‘charged’
battery, then start the machine that has the
‘dead’ battery.
•
Remove the jumper cables in the exact
reverse order of connecting. Do not allow the
cable clamps to touch any metal parts while
the other end is connected to a battery
terminal.
IMPORTANT
Keep the battery terminals clean. Smear them
with white grease to prevent corrosion.
The positive terminal (red) protective cover must
be kept in place.
Summary of Contents for RoboMax
